Hotplates and Stirrers
Research Products International Corp Digital Hot Plate Stirrer, 12 x 12 Inch Ceramic Top
The EchoTherm HS51 is designed to be the easiest to use and most accurate fully featured stirring hot plates in the world. Temperature measurement of a solution is accurate to 1% over the entire temperature range using a 100 ohm platinum RTD sensor and measurement system. Calibration of temperature is electronic and stored in memory. The calibration is set at the factory but can be done easily in the field using the probe calibration kit offered as an accessory. The chassis on both models is cast aluminum designed to keep spills and heat out of the electronics. They are coated with chemically resistant epoxy based paint for durability.
Ace Glass, Inc. Complete Trubore bearing, 19mm ID, 34/45 adapter plus inner bearing and bushing
34/45 TRUBORE BEARING C
Ace Glass, Inc. Motor controller ac/dc input:120v 60Hz 10a max.
A compact, lightweight, solid state, ring stand mountable control unit, both AC and DC outlets. Rated 1 hp. for use with most stirrer motors. AC output: 120 volts, 10 amps. DC output: 0-120 volts, 6 amps.
Chemglass Life Sciences PEEK Compression Cap, 19mm
Grease-Free PTFE stirrer bearing for use under moderate vacuum. The bearing consists of a PTFE standard taper body, PEEK (Polyetheretherketone) compression cap, PTFE Insert/bushing and a Nylon loosening nut. The PTFE insert/bushing provides only glass and PTFE contact with the reaction. Loosening nut above the standard taper inner joint allows easy and quick removal. Supplied complete with a Perfluoro o-ring on the body and a Viton o-ring on the bushing.
Chemglass Life Sciences 30mm PTFE Stirrer Bearing, 45/50, #129 Body O-Ring, #027 Bushing O-Ring
Grease-Free PTFE stirrer bearing for use under moderate vacuum. The bearing consists of a PTFE standard taper body, PEEK (Polyetheretherketone) compression cap, PTFE Insert/bushing and a Nylon loosening nut. The PTFE insert/bushing provides only glass and PTFE contact with the reaction. Loosening nut above the standard taper inner joint allows easy and quick removal. Supplied complete with a Perfluoro o-ring on the body and a Viton o-ring on the bushing.
Grainger Motor 1 1/2 HP 3 450 rpm 115/208-230V
The Tripp Lite 16U SmartRack Wall Mount Rack Enclosure Cabinet is a 16U wall-mountable rack that provides a sturdy way to mount rack equipment in network closets, back offices and other areas with limited floor space. It is constructed with steel for durability and vented sides for proper airflow. The mounting rails adjust in 1/4" increments to accommodate equipment up to 20.5" deep. The front and rear pairs of vertical rails have square mounting holes that allow easy equipment installation. This 16U wall mount rack has a weight capacity of 200 lbs.
Ace Glass, Inc. Stirbar, PTFE, octagonal, blue, 25.4mmx8.0mm
25.4mm x 8.0mm blue octagonal PTFE stirbar with pivot ring.
Ace Glass, Inc. Stirbar, PTFE, octagonal, yellow, 76.2mmx12.7mm
Stirbar, PTFE, octagonal, yellow, 76.2mmx12.7mm
Electron Microscopy Sciences Lower Shaft Assembly for Model 865 Diamond Band Saw
For use with Model 865 Daimond Band Saw (50182-65).
Chemglass Life Sciences 30mm Stirrer Shaft Coupling, Universal, 3/8" OD Stud
30mm Stirrer Shaft Coupling, Universal, 3/8" OD Stud. Coupling incorporates a universal joint to compensate for misalignment of drive motor and glass stirrer shaft. Nylon bushing compresses around shaft using an allen screw. Stainless Steel stud attaches directly to the chuck of a stirrer motor. Supplied complete with an allen wrench.